Mobile health vehicles

Article Sub-Headings

Mobile Health Vehicles

We are also proud to present to you that our Mobile Health Vehicles are a platform supported by the United Nations.As Ambulancemed EOW group company, we make great efforts to serve our customers in the best facilities and on the best terms. Due to the recent and still ongoing pandemic, we are providing our products to you with precision and care in terms of health and in providing this service.

As Ambulancemed EOW group, we are expanding our equipment and vehicles consisting of the comfortable and best technologies that we provide for you no matter what conditions are in worldwide.

Our Mobile Health Vehicles are  high-quality mobile health vehicle’s floor, ceiling, side panel coverings, and cupboards are manufactured with special materials convenient for vehicle modification  therewithal our  medical devices and equipment designed

In our Mobile health vehicles consist of a total of 8 vehicles, each equipped with different equipment for health solutions. Mobile surgery equipment, mobile operating room equipment, sterilization equipment, diagnostic equipment, x-ray equipment, mammography and many other health equipment such as functionally equipped.

And therewithal Our  Mobile Health Vehicle is equipped with 15 KW generator, UPS and illumination lamps operated with external mains power and can give 220 V outside.

Health workers also played an active role in the production of  our Mobile Health Vehicle project for export to Yemen and the installation, location and materials used for each equipment were evaluated according to health criteria. All equipment used are approved by the Ministry of Health and comply with health criteria. When we examine the general characteristics of the vehicles designed for 3 categories and 3 different purposes;

1- Emergency – general surgery – operating room and post op (postoperative)

2- X-ray – Laboratory – Pharmacy – Internal medicine policlinics

3- X-ray – Laboratory – Pharmacy

         – Polyclinic / children-ENT

         – Polyclinic / Gynecology – Orthopedic – General surgery

4 – Industrial Screening Hearing Test

5 – Respiratory Function Test

6 – Taking samples for blood tests

-The following examinations are carried out in our simple service laboratory on the samples taken;

Non-automated urine analysis with reagents in the form of strips or tablets

– Hidden blood in the feces

– Blood glucose (with glucose monitoring devices specifically approved for home use)

– Hemoglobin (with non-automatic techniques or simple devices that give a direct result)

are grouped as.

– Heat-resistant composite materials and durable monoblock walls

– Hydraulic foot, foldable ladder, wheelchair ramp and guardrails

– Interior lighting, air conditioning, Generator, electrical sockets, locking doors, sliding interior doors

– Sun visor on exterior doors and door hydraulics on interior doors

– Solar energy system and panel (optional – for Ecuador countries)

– Waste and clean water tank

– Sink, lighting and ventilation windows

As group of company Ambulancemed EOW, Mobile Health Vehicles, we custom design mobile vehicles for the Vision industry. We engineer each vehicle in house and work diligently to bring each customer’s vision to life while maintaining dimensions, keeping in mind ergonomics, and using the necessary permits and clearances. Our turn-key service ensures that every client will receive a mobile health unit that is designed and engineered to specifically meet how our As Ambulancemed EOW customers need. Find out more about our custom vision vehicles below.

As group of we provide all periodic inspection services within the scope of the laws and regulations related to our fully equipped mobile health vehicles.

The main disadvantage of the prototype is the inability to carry out X-ray diagnostic measures when providing qualified and specialized medical care to the wounded in wartime and victims of natural disasters, accidents and disasters of peacetime in the field.

The disadvantages of the prototype are also that there is no automation and prompt receipt of radiographs in the field. Today, chemical and photographic processing of X-ray film in field photo labs is done manually using tanks and cuvettes. Processing of one sheet of film, including development, fixing and washing, takes at least 30 minutes. Taking into account drying, it is even larger. The number of simultaneously processed films is small, and the quality of the resulting radiographs largely depends on the time and temperature conditions of processing. The high labor intensity of the process and its low automation is largely explained by the low throughput of field photo labs. On the flip side, the low reliability of the electric X-ray machines available in the supply, as well as the low mechanical and thermal strength of selenium plates, does not allow us to abandon film X-ray now.

Moreover, in our Mobile Health Vehicles are  the brightness of the glow of the screen of the X-ray machine with radiation loads acceptable from the point of view of safety is small, it is only 0.01 cd / m2, therefore, X-ray is ineffective. If, at normal image brightness, details with a contrast of 2-3% are easily detected, then the minimum distinguishable contrast is 10-12%. Therefore, in his desire to improve the quality of diagnostics, the radiologist is forced to increase the current strength, and consequently, the radiation dose of the wounded. As a result, it is necessary to increase the information content of images and reduce radiation loads based on the use of promising radiographs.

The drawing shows a block diagram of a mobile medical vehicle.

As group of Ambulancemed EOW, our a mobile health vehicle contains van bodies with an air purification and ventilation system, divided by partitions into compartments with medical equipment installed in them, a 1K23 air conditioner with a control panel and an air duct, heater control devices and a filter ventilation unit, a linear input for connecting communication cables, control and monitoring during vehicle operation, an intercom device, fire extinguishers and tools, TA-57 telephones, pads and sockets for connecting devices to the 220V network are fixed on the walls, and outside the van bodies there is a heating and ventilation unit of the OV-65 type, a filter ventilation unit of the FVU-100N-12 type, fuel tanks and batteries.

We have mentioned to you above the most basic features of our Mobile Health Vehicle for what purpose it is used. Below I would like to point out to you the additional elements where our Mobile Health Vehicles are used according to the activities;

In the our Mobile Health Vehicle additionally contains the following elements and components:

1 – Mobile X-ray diagnostic complex,

2, A hardware machine (РК100) x-ray Department,

3 – Pneumovagina medical class PSM-4, x – ray Department

4 – Power energy office,

5 – X-Ray protection partition,

6 – Control module,

7 – Fluorographic cabin,

8 – X-Ray installation,

9 – X-Ray camera type KF-70T,

10 – Docking unit with camera 9,

11 – Development machine type FP-104,

12 – Collapsible X-ray machine of the Rapid-1 type,

13 – Electric diesel unit of the AD-16-T/400-A1R type,

14 – Digital medical radiotelevisorography system,

15 – Block of multi-frame memory of X-ray television images,

16 – Portable portable personal computer,

17 – Infrared transceiver,

18 – Infrared port,

19 – Scanner,

20 – Printer,

21 – Control panel,

22 – Radiologist’s desk,

23 – Adaptive local lighting lamp,

24 – Cans for collecting developer, fixer and water solutions,

25 – Canister for feeding the washing unit with fresh water,

26 – Drying machine unit 11,

27 – Fan,

28 – Washing compressor system,

29 – Pumping elements-water heating up to 60oC,

30 – Cabinet with medical equipment,

31 – X-ray laboratory table,

32 – Rotating chair,

33 – Sets of concentrated solutions of chemicals “X-ray-6”,

34 – ZIP,

35 – Unit for the preparation of radiopaque suspension,

36 – Control panel of the fluorography unit 8,

37 – Steel enameled cuvettes for developing films,

38 – Double-leaf door for access to the fluorography cabin,

39 – Leaded glass for patient observation,

40 – Air hose from the filter ventilation unit,

41 – Side door,

42 – X-ray curtain,

43 – Frame with camera 9 (KF-70T),

44 – Lift for patient accommodation,

45 – Lift and lower lift buttons,

46 – Monoblock frames,

47 – Monoblock stand,

48 – A monoblock from the Rapid-1 type X-ray machine 12,

49 – Elements for regulating and fixing the position of the monoblock,

50 – Remote control panel of the electric unit 13,

51 – Non-actinic lighting lamp,

52 – Controls,

53 – Steel shutters,

54 – A window made in the partition 5 for the transfer of film,

55 – A photo lab table,

56 – Hole,

57 – The hood,

58 – Detection unit BDMG-36,

59 – Case,

60 – Steel frame,

61 – Guides,

62 – Ball bearings,

63 – Electric motor,

64 – Magnetic starter,

65 – Controlled trolley,

66 – Ceiling light,

67 – Air vent,

68 – Dark red light filter,

69 – Spherical reflector,

70 – Car lamp for 24 V,

71 – Knobs for adjusting the illumination,

72 – Portable ultrasonic device “Scud 9210”,

73 – Negatoscope,

74 – Tables of a doctor and an X-ray technician,

75 – Chairs of a doctor and an X-ray technician,

76 – Switchboard,

77 – Military chemical reconnaissance device,

78 – Chemical reconnaissance device holder,

79 – Stretcher stands,

80 – Auto-lock cards,

81 – Aggregate compartment,

82 – Rigging compartment,

83 – Rods for fencing the hazardous area of X-ray separation,

84 – Power shield,

85 – Stand,

86 – Control panel,

87 – Power supply unit,

88 – X-ray separation equipment, spare parts and consumables,

89 – Unit for drinking water,

90 – Cabinets,

91 – Folding chair,

92 – Rods for unit 13 and grounding,

93 – Coil with cables,

94 – Furniture,

95 – Power shield,

96 – Protective screens,

97 – Plywood board-card coverings,

98 – Standard insulation made of 24 heat-insulating mats,

99 – Rubber carpet,

100 – Transitional vestibule,

101 – Entrance vestibule.

Optional design options are available for all these and different additional options. Please contact us for detailed information.

Ambulance Manufacturers

Find another article by searching.

Other articles to read

Archives

The Countries

To see the projects sent to each country, you can click on the button of that country.

Contact us

info@ambulancemed.com

+90 554 969 5008

Dağyaka Mah. 2018 Sk. No:23 Aksan Ticaret Merkezi Kahramankazan / Ankara